Diode House

SOT-23/SOT-23-3L Encapsulate
SI2300 SI2301 SI2302 SI2303 SI2304
SI2305 SI2306 SI2307 SI2308 SI2309
SI2312 SI2315 SI2317 SI2323 2N7002
SK3018 BSS138 BSS123

A03400 A03401 A03402 A03403 A03404 A03406 A03407 A03409
A03410 A03413 A03415 A03420

TO-92 SMD Plastic Package
2N7000 1N45 1N50 1N60 1N80

SOP-8 Encapsulate
4401 4402 4406 4407 4410
4420 4435 4606 4614 4803
4812 4920 4953 9926 9435

TO-252 eNCAPSULATE
1N60 2N60 4N60 10N06 10P06

Additional Information:

• Port of Dispatch: MUMBAI
• Delivery Time: EX-Stock

Toshiba Gen-4 Super-Junction DTMOSIV MOSFETs use the state-of-the-art single epitaxial process DTMOSIV, which provides a 30% reduction in RDS(on), a figure of merit (FOM) for MOSFETs, compared to its predecessor, DTMOSIII. With a reduction in the RDS(on) it makes it possible to house lower RDS(on)chips in the same packages. This helps to improve the efficiency and reduce the size of power supplies. These devices are ideal for use with switching regulators.

Features:

• Low drain-source on-resistance
• Easy to control Gate switching
• Enhancement mode: Vth = 2.7 to 3.7V
• 30% reduction in RDSon*A compared to previous generation
• Improved figure of merit (FOM) compared to DTMOS III generation
• Reduction in Coss
• Application of latest process technology: single epitaxial process
• Wide range of on-resistances and packaging options
• 45% reduction of Qgd (gate drain charge) at X-Series

Applications:

• Switched Mode Power Supply (SMPS)
• Lighting
• Power Factor Control (PFC)
• Industrial Applications (including UPS)

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

Based on Avia Semiconductor’s patented technology, HX710(A/B) is a precision 24-bit analog-to-digital converter (ADC) with built-in temperature sensor (HX710A) or DVDD, AVDD voltage difference detection (HX710B). It’s designed for weigh scales and industrial control applications to interface directly with a bridge sensor. The input low-noise amplifier (PGA) has a fixed gain of 128, corresponding to a full-scale differential input voltage of ±20mV, when a 5V reference voltage is connected to the VREF pin. On chip oscillator provides the system clock without any external component. On-chip poweron-reset circuitry simplifies digital interface initialization. There is no programming needed for the internal registers. All controls to the HX710 are through the pins.

Features:

• On-chip temperature measurement (HX701A)
• DVDD and AVDD supply voltage difference measurement (HX701B)
• On-chip low noise amplifier with a gain of 128
• On-chip oscillator requiring no external component
• On-chip power-on-reset

Simple digital control and serial interface:

• Pin-driven controls, no programming needed
• Selectable 10SPS or 40SPS output data rate
• Simultaneous 50 and 60Hz supply rejection

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: Ready Stock

Components which are sensitive to electrostatic discharges are packed with due caution in special ESD zone. For this purpose, we use antistatic rails or blisters filled with antistatic ether foam. All products from ESD zone are also packed in shielding bags.

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

Description TinySwitch™-II integrates a 700 V power MOSFET, oscillator, high voltage switched current source, current limit and thermal shutdown circuitry onto a monolithic device. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias winding and associated circuitry. In addition, the TinySwitch-II devices incorporate auto-restart, line undervoltage sense, and frequency jittering. An innovative design minimizes audio frequency components in the simple ON/OFF control scheme to practically eliminate audible noise with standard taped/varnished transformer construction. PI-2684-061815 Wide-Range High-Voltage DC Input D S EN/UV BP + - + - DC Output TinySwitch-II Optional UV Resistor The fully integrated auto-restart circuit safely limits output power during fault conditions such as output short circuit or open loop, reducing component count and secondary feedback circuitry cost. An optional line sense resistor externally programs a line undervoltage threshold, which eliminates power down glitches caused by the slow discharge of input storage capacitors present in applications such as standby supplies. The operating frequency of 132 kHz is jittered to significantly reduce both the quasi-peak and average EMI, minimizing filtering cost.

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

NE556 Dual Bipolar TimersNE556 provides two independent timing circuits of the NA555, NE555, SA555, or SE555 type in each package. These circuits can be operated in the astable or monostable mode with external resistor-capacitor(RC) timing control. the basic timing provided by the RC time constant can be controlled actively by moduling the bias of the control-voltage input.

Features of NE556:

• Low turn-off time
• Timing from microseconds to hours
• Operates in both astable and monostable modes
• Adjustable duty cycle
• TTL compatible

Bright Power Semiconductor -Led Driver Ic:

• BP9911A
• BP9911B
• BP9911CB
• BP9911CC
• BP9912A
• BP9912B
• BP9912CB
• BP9912C
• BP9918A
• BP9918B
• BP9918CB
• BP9918C
• BP9916A
• BP9916B
• BP9916CB
• BP9916C
• BP9916D
• BP9921C
• BP9926C
• BP9926D
• BP9736B
• BP2831A
• BP2831AJ
• BP2831K
• BP2832A
• BP2832AJ
• BP2832K
• BP9833A
• BP2833A
• BP2833K
• BP2836A
• BP9833D
• BP2833D
• BP2836D
• BP2857D
• BP2865E
• BP2839A
• BP2333
• BP2335J
• BP2336J
• BP2338J
• BP2325AJ
• BP2326AJ
• BP2327AJ
• BP2328AJ
• BP2328DJ
• BP2329AJ
• BP5136H
• BP5131DC
• BP5131SC
• BP5131HC
• BP5151HC
• BP5152HC
• BP5158H
• BP9116B
• BP3122B
• BP3135
• BP3135D
• BP3163D
• BP9021A
• BP9022A
• BP3133A
• BP3122
• BP3125
• BP3126S
• BP3126
• BP3106
• BP3105
• BP3316D
• BP3315
• BP3316
• BP3319MB
• BP3211
• BP3212
• BP3216
• BP3216E
• BP3218
• BP3236C
• BP3238
• BP1360
• BP1361
• BP1808
• UR4205C
• UR3311
• BP5609
• BP5619
• BP3198
• BP2882
• BP2888
• BP2888A
• BP5912A
• BP5912B
• BP5910
• BP5911
• BP5901
• BP2838
• BP2838G
• BP2838H
• BP2871
• BP2872
• BP2318
• BP3318
• BP3516C
• BP3519
• BP2519
• BP2516F
• BP2513D
• BP3319
• BP3329

Diode House is a trading organization of Electronic Components catering to requirements of electronics industries in India. Established in 1994, Diode House is a leading supplier for all types of active and passive components and distributors for various manufacturing companies such as CDIL, Desai Electronics, Watt Electronics, Sree Solder and Kwality Photonics.

Additional Information:

• Port of Dispatch: MUMBAI
• Delivery Time: EX-STOCK

6N139 High Speed Opto-coupleris High common mode transient immunity and very high current ratio together with 5300 VRMSinsulation are achieved by coupling and LED with an integrated high gain photo detector in an eight pin dual-in-line package. Separate pins for the photo diode and output stage enable TTL compatible saturation voltages with high speed operation. Access to the base terminal allows adjustment to the gain bandwidth. The 6N138 is ideal for TTL applications since the 300 % minimum current transfer ratio with an LED current of 1.6 mA enables operation with one unit load-in and one unit load-out with a 2.2 kO pull-up resistor. The6N139 optocoupleris best suited forlow powerlogic applications involving CMOS and low power TTL. A 400 % current transfer ratio with only 0.5 mA of LED current is guaranteed from 0 DegreeC to 70 DegreeC.

Features of 6N139 High-Speed Optocoupler

• High current transfer ratio, 300 %
• Low input current, 0.5 mA
• High output current, 60 mA
• Isolation test voltage, 5300 VRMS
• TTL compatible output, VOL = 0.1 V
• High common mode rejection, 500 V/s
• Adjustable bandwidth-access to base

 

Applications of 6N139 High-Speed Optocoupler:

• Microprocessor system interface
• PLC, ATE input / output isolation
• EIA RS232 line receiver
• TTL, CMOS voltage level translation
• Multiplexed data transmission
• Digital control power supply

• Ground loop and electrical noise elimination

LNK364 Low Power Off-Line Switcher ICLinkSwitch-XT incorporates a 700 V power MOSFET, oscillator,simple ON/OFF control scheme, a high-voltage switched currentsource, frequency jittering, cycle-by-cycle current limit andthermal shutdown circuitry onto a monolithic IC. The startupand operating power are derived directly from the DRAINpin, eliminating the need for a bias winding and associatedcircuitry.

Features of LNK364:

• Optimized for Lowest System Cost
• Proprietary IC trimming and transformer constructiontechniques enable Clampless(TM) designs with LNK362for lower system cost, component count and higherefficiency
• Fully integrated auto-restart for short circuit andopen loop protection
• Self-biased supply - saves transformer auxiliary windingand associated bias supply components
• Frequency jittering greatly reduces EMI
• Meets HV creepage requirements between DRAIN andall other pins both on the PCB and at the package
• Lowest component count switcher solution
• Accurate hysteretic thermal shutdown protection -automatic recovery improves field reliability
• Universal input range allows worldwide operation
• Simple ON/OFF control, no loop compensation needed
• Eliminates bias winding - simpler, lower costtransformer
• Very low component count - higher reliability and singleside printed circuit board
• Auto-restart reduces delivered power by 95% duringshort circuit and open loop fault conditions
• High bandwidth provides fast turn-on with no overshootand excellent transient load response
• Extremely Energy Efficient
• Easily meets all global energy efficiency regulations withno added components
• No-load consumption <300 mW without bias winding at265 VAC input (<50 mW with bias winding)
• ON/OFF control provides constant effi ciency to verylight loads - ideal for mandatory CEC regulations

LM393 Low Offset Voltage Dual ComparatorLM393 is a dual precision voltagecomparator IC capable of single or dual supply operation.LM393 ICisdesigned to permit a common mode rangetoground level withsingle supply operation. Input offset voltage specifications as low as2.0 mVolt make this device an excellent selection for many applicationsin consumer, automotive, and industrial electronics.LM393 IC is used in most of the digital comparator Modules that is used in GAS sensor modules, rain sensors etc.

Features of LM393 Comparator IC:

• Very Low Current Drain Independent of Supply Voltage 0.4 mA

• Low Input Offset Voltage 5.0 mV (max) LM293/393

• Input Common Mode Range to Ground Level

• Differential Input Voltage Range Equal to Power Supply Voltage

• Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS Logic Levels

• These Devices are PbFree, Halogen Free/BFR Free and are RoHS Compliant

TNY264 Low Power Off-line SwitcherTinySwitch-II maintains the simplicity of the TinySwitch topology, while providing a number of new enhancements to further reduce system cost and component count, and to practically eliminate audible noise. Like Tiny Switch, a 700 V power MOSFET, oscillator, high voltage switched current source, current limit and thermal shutdown circuitry are integrated onto a monolithic device. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias winding and associated circuitry. In addition, the TinySwitch-II devices incorporate auto-restart, line under voltage sense, and frequency jittering.An innovative design minimizes audio frequency components in the simple ON/OFF control scheme to practically eliminate audible noise with standard taped/varnished transformer construction.TNY264fully integrated auto-restart circuit safely limits output power during fault conditions such as output short circuit or open loop, reducing component count and secondary feedback circuitry cost. An optional line sense resistor externally programs a line under-voltage threshold, which eliminates power down glitches caused by the slow discharge of input storage capacitors present in applications such as standby supplies. The operating frequency of132 kHzis jittered to significantly reduce both the quasi-peak and average EMI, minimizing filtering cost.

Features of TNY264 Low Power Off-line Switcher

• Fully integrated auto-restart for short circuit and open loop fault protection-saves external component costs
• Built-in circuitry practically eliminates audible noise with ordinary varnished transformer
• Programmable line under-voltage detect feature prevents power on/off glitches-saves external components
• Frequency jittering dramatically reduces EMI (~10 dB) -minimizes EMI filter component costs
• 132 kHz operation reduces transformer size-allows use of EF12.6 or EE13 cores for low cost and small size
• Very tight tolerances and negligible temperature variation on key parameters eases design and lowers cost
• Lowest component count switcher solution

The TNY267 IC maintains the simplicity of the TinySwitch topology, while providing a number of new enhancements to further reduce system cost and component count, and to practically eliminate audible noise. Like Tiny Switch, a 700 V power MOSFET, oscillator, high voltage switched current source, current limit and thermal shutdown circuitry are integrated onto a monolithic device. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias winding and associated circuitry.

 

Features of TNY267 IC:

• Fully integrated auto-restart for short circuit and open loop fault protection-saves external component costs
• Built-in circuitry practically eliminates audible noise with ordinary varnished transformer
• Programmable line under-voltage detect feature prevents power on/off glitches-saves external components
• Frequency jittering dramatically reduces EMI (~10 dB) -minimizes EMI filter component costs
• Very tight tolerances and negligible temperature variation on key parameters
• High voltage powered-ideal for charger applications
• High bandwidth provides fast turn on with no overshoot
• Current limit operation rejects line frequency ripple Built-in current limit and thermal protection

Diode House suppling Intergrated Circuit full range. 

Diode House is a trading organization of Electronic Components catering to requirements of electronics industries in India. Established in 1994, Diode House is a leading supplier for all types of active and passive components and distributors for various manufacturing companies such as CDIL, Desai Electronics, Watt Electronics, Sree Solder and Kwality Photonics.

Additional Information:

• Delivery Time: Ex-Stock

The74LS02 Quad 2-Input NOR Gateis a 14 pin IC which contains four independent gates each of which performs the logic NOR function. The IC is adual in - line packagewhose 14 & 7 no. pin is vcc&gnd, 2 & 3 in and 1 out, 5 & 6 in and 4 out, 8 9 in and 10 out, 11 & 12 in and 13 is out. The package may be through-hole mounted to a printed circuit board or inserted in a socket. Because of DIP package the device is able to perform ideally even at 70 DegreeC.

We are one of the leaduing wholesale traders and suppliers of SIC9753 DIP-7 IC LED Driver IC.

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock
• Packaging Details: 2000Pcs

The RHRG30120 is a hyper-fast diode with soft recovery characteristics. It has the half recovery time of ultra-fast diodes and is silicon nitride passivated ion implanted epitaxial planar construction.RHRG30120 diodedevice is intended to be used asfreewheeling/ clamping diodes and diodes in a variety of switching power supplies and other power switching applications. Their low stored charge and hyper-fast soft recovery minimize ringing and electrical noise in many power switching circuits reducing power loss in the switching transistors.

 

Features of RHRG30120 Hyper-fast Diode:

• Hyper-fast recovery Trr = 85ns (@IF= 30A)
• Max Forward Voltage, VF = 3.2V (@ TC = 25 DegreeC)
• Avalanche Energy Rated
• RoHS compliant
• Package / Case TO-247
• If - Forward Current 30 A
• Configuration Single

 

Application of RHRG30120 Hyper-fast Diode:

• Uninterruptible Power Supply

W78E052DDG is 8051 compatible 8-bit controller from Nuvoton with 8K programmable flash memory in 40 Pin DIP package. Wide operating voltage 2.4 - 5.5V, at 12 clock default per machine cycle it can achieve maximum 40 MHz. Peripheral includes Timer, counter, interrupt, watchdog timer and 4 ports and default configuration fully compatible with 80C52. This chip has separate dedicated 2K boot-loader memory, which makes this chip robust and very stable compare to other in this category. The chances of boot-loader erased or corrupted by user program or error are negligible. It supports ISP program downloading from PC using RX-TX lines only. Software for downloading is provided by the company free of cost.

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

MCT2E OptoisolatorMCT2E optoisolator consist of a gallium arsenide infrared emitting diode driving a silicon photo-transistor in a 6-pin dual in-line package.

Features of MCT2E:

• Operating Temperature TOPR-55 to +100 DegreeC
• Lead Solder Temperature TSOL260 for 10 sec DegreeC
• Collector-Emitter Voltage VCEO30 V
• Detector Power Dissipation @ TA= 25 DegreeC 150 mW

Applications of MCT2E:

• Power supply regulators
• Digital logic inputs
• Microprocessor inputs

IRS2110 MOSFET and IGBT Driver ICIRS2110 is high voltage, high speedpower MOSFET and IGBT driverswith independent high-side and low-side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. Logic inputs are compatible with standard CMOS or LSTTL output, down to 3.3 V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channel can be used to drive anN-channel power MOSFET or IGBTin the high-side configuration which operates up to 500 V or 600 V.

Features of IRS2110 High and Low Side Driver IC:

• Floating channel designed for bootstrap operation
• Fully operational to +500 V or +600 V
• Tolerant to negative transient voltage, dV/dt immune
• Gate drive supply range from 10 V to 20 V
• Undervoltage lockout for both channels
• 3.3 V logic compatible
• Separate logic supply range from 3.3 V to 20 V
• Logic and power ground +- 5V offset
• CMOS Schmitt-triggered inputs with pull-down
• Cycle by cycle edge-triggered shutdown logic
• Matched propagation delay for both channels
• Outputs in phase with inputs
• RoHS compliant

ULN2003 High Current Seven Darlington Transistor ArraysThe ULN2003 is a monolithic high voltage and high current Darlington transistor arrays. It consists of seven NPN darlington pairs that features high-voltage outputs with common-cathode clamp diode for switching inductive loads. The collector-current rating of a single darlington pair is 500mA. The darling ton pairs may be paralleled for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers(LED gas discharge),line drivers, and logic buffers. The ULN2003 has a 2.7kseries base resistor for each darlington pair for operation directly with TTL or 5V CMOS devices.


Features of ULN2003:

• 500mA rated collector current(Single output)
• High-voltage outputs 50V
• Inputs compatible with various types of logic.
• Relay driver application

ULN2803 High Current NPN Darlington Transistor ArrayThe eight NPN Darlington connected transistors in this family of arrays are ideally suited for interfacing between low logic level digital circuitry (such as TTL, CMOS or PMOS/NMOS) and the higher current/voltage requirements of lamps, relays, printer hammers or other similar loads for a broad range of computer, industrial, and consumer applications. All devices feature open-collector outputs and free wheeling clamp diodes for transient suppression. The ULN2803 is designed to be compatible with standard TTL families while the ULN2804 is optimized for 6 to 15 volt high level CMOS or PMOS.

An integrated circuit, or IC, is small chip that can function as an amplifier, oscillator, timer, microprocessor, or even computer memory. An IC is a small wafer, usually made of silicon, that can hold anywhere from hundreds to millions of transistors, resistors, and capacitors.

Additional Information:

• Delivery Time: Ex-Stock

dsPIC 30F3010High-Performance,16-Bit Digital Signal ControllersThis is a 28 pin high performance 1- bit dsPIC series Micro-controller from Microchip.

Features of dsPIC30F3010:

• High-Performance Modified RISC CPU
• Modified Harvard architecture
• C compiler optimized instruction set architecture
• 84 base instructions with flexible addressing modes
• 24-bit wide instructions, 16-bit wide data path
• 16 x 16-bit working register array
• Up to 30 MIPs operation
• DC to 40 MHz external clock input
• 4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)
• Peripheral and External interrupt sources
• 8 user selectable priority levels for each interrupt
• 4 processor exceptions and software traps
• Primary and Alternate interrupt Vector Tables

dsPIC30F3010 Engine Features:

• Modulo and Bit-Reversed Addressing modes
• Two, 40-bit wide accumulators with optional saturation logic
• 17-bit x 17-bit single cycle hardware fractional/ integer multiplier
• Single cycle Multiply-Accumulate (MAC) operation
• 40-stage Barrel Shifter
• Dual data fetch

dsPIC30F3010Peripheral Features:

• High current sink/source I/O pins 25 mA/25 mA
• Optionally pair up 16-bit timers into 32-bit timer modules
• 3-wire SPI(TM) modules (supports 4 Frame modes)
• I2C(TM) module supports Multi-Master/Slave mode and 7-bit/10-bit addressing
• Addressable UART modules with FIFO buffers

Motor Control PWM Module Features:

• Complementary or Independent Output modes
• Edge and Center Aligned modes
• Multiple duty cycle generators
• Dedicated time base with 4 modes
• Programmable output polarity
• Dead time control for Complementary mode
• Manual output control
• Trigger for synchronized A/D conversions

Quadrature Encoder Interface Module Features:

• Phase A, Phase B and Index Pulse input
• 16-bit up/down position counter
• Count direction status
• Position Measurement (x2 and x4) mode
• Programmable digital noise filters on inputs
• Alternate 16-bit Timer/Counter mode
• Interrupt on position counter rollover/underflow

Analog Features of dsPIC30F3010:

• 10-bit 1 Msps Analog-to-Digital Converter (A/D)
• A/D Conversion available during Sleep and Idle
• 4 Sample/Hold Channels
• Multiple Conversion Sequencing Options

Special Microcontroller Features:

• Enhanced Flash program memory10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)
• Data EEPROM memory100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)Self-re-programmableunder software control

• Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer(OST)
• Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliableoperation
• Fail-Safe clock monitor operation
• Detects clock failure and switches to on-chip low power RC oscillator
• Programmable code protection
• In-Circuit Serial Programming(TM) (ICSP(TM))
• Programmable Brown-out Detection and Reset generation
• Selectable Power Management modes
• Sleep, Idle and Alternate Clock modes

CMOS Technology:

• Low power, high speed Flash technology
• Wide operating voltage range (2.5V to 5.5V)
• Industrial and Extended temperature ranges
• Low power consumption

The TOP250YN IC is a 135W extended power design flexible integrated Off-line Switcher uses the same proven topology as TOPSwitch and it integrating thehigh voltage power MOSFET, PWM control, fault protectionand other control circuitry onto a single CMOS chip. Many new functions are integrated to improve design flexibility, performance and energy efficiency. Line feed-forward with maximum duty cycle (DCMAX) reduction rejects line ripple and limits DCMAX at high line.


Features of TOP250YN Power Integrations IC:

• Eliminate or reduce cost of external components
• Fully integrated soft-start for minimum stress/over-shoot
• Externally programmable accurate current limit
• Wider duty cycle for more power, smaller input capacitor
• Line under-voltage detection - No turn OFF glitches
• Line over-voltage shutdown extends line surge limit
• Regulates to zero load without dummy loading
• Hysteretic thermal shutdown for automatic fault recovery
• Large thermal hysteresis prevents PC board over-heating
• xtremely low consumption in remote off mode
• Frequency lowered with load for high standby efficiency
• Allows shutdown/wake-up via LAN/input port

Specifications of TOP250YN Power Integrations IC:

• Input Voltage AC Min 85V
• Input Voltage AC Max 265V
• Operating Temperature Min -40 DegreeC
• AC / DC Converter Case Style TO-220
• Fault Protection Current Limiting, Over Temperature, Over Voltage
• Control Features Frequency Control
• No. of Pins 6Pins
• Topology Flyback
• Voltage - Breakdown 700V
• Topology Flyback

Incepted in the year 2005, Diode House is the renowned wholesale trader of a superb quality collection of Industrial Electronics Components items Zener Diode, Diode, Resistor, SMD Resistor, Capacitor, Intergrated Circuit(IC), trimpot's, Transistor, LED, Tantlum, MOV, NTC, JHD Display etc and much more.

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

ATMEL AVR ATtiny 45 Micro-controllerThe high-performance, low-power Atmel 8-bit AVR RISC-based microcontroller combines 4KB ISP flash memory, 256-Byte EEPROM, 256B SRAM, 6 general purpose I/O lines, 32 general purpose working registers, one 8-bit timer/counter with compare modes, one 8-bit high speed timer/counter, USI, internal and external Interrupts, 4-channel 10-bit Analog to Digital converter, programmable watchdog timer with internal oscillator, three software selectable power saving modes, and debugWIRE for on-chip debugging. The device achieves a throughput of 20 MIPS at 20 MHz and operates between 2.7-5.5 volts.By executing powerful instructions in a single clock cycle, the device achieves throughputs approaching 1 MIPS per MHz, balancing power consumption and processing speed.


Features of ATtiny-45 Micro-controller:

• Flash (Kbytes): 4 Kbytes
• Pin Count: 8
• CPU: 8-bit AVR
• Max I/O Pins: 6
• Ext Interrupts: 6
• USB Interface: No

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: Ex-Stock

SG3525 Pulse Width ModulatorThere are numerous Pulse Width Modulation (PWM) controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers - ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few.
The SG3525A pulse width modulator control circuit offersimproved performance and lower external parts count whenimplemented for controlling all types of switching power supplies.The on1% and the erroramplifier has an input commonmode voltage range that includes thereference voltage, thus eliminating the need for external dividerresistors. A sync input to the oscillator enables multiple units to beslaved or a single unit to be synchronized to an external system clock.A wide range of dead time can be programmed by a single resistorconnected between the CT and Discharge pins. This device alsofeatures builtin softstart circuitry, requiring only an external timingcapacitor. A shutdown pin controls both the softstart circuitry and theoutput stages, providing instantaneous turn off through the PWM latchwith pulsed shutdown, as well as softstart recycle with longershutdown commands. The under voltage lockout inhibits the outputsand the changing of the softstart capacitor when VCC is belownominal. The output stages are totempole design capable of sinkingand sourcing in excess of 200 mA. The output stage of the SG3525Afeatures NOR logic resulting in a low output for an offstate.


Features of SG3525:

• Separate Oscillator Sync Pin
• Adjustable Deadtime Control
• Input Undervoltage Lockout
• Latching PWM to Prevent Multiple Pulses
• PulsebyPulse Shutdown

Application of SG3525:

• Motor Control
• DC-DC Convertor
• DC-AC Inverter
• Lamp Dimmers

L293D H-Bridge Driver ICL293D is a quadruple high current half-H drivers. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 36 V. Both devices are designed to drive inductive loads such as relays,solenoids, DC and bipolar stepping motors, as well as other high-current/high-voltage loads in positive supply applications.

Features Of L293D Ic:

• Per Channel
• Enable Facility
• Overtemperature Protection
• Internal Clamp Diodes

MOSFET Transistors - IRF Series:

• IRF150 38A 100V N-Channel Power MOSFET
• IRF250 30A 200V N-Channel Power MOSFET
• IRF350 14A 400V N-Channel Power MOSFET
• IRF510 5.6A 100V N-Channel Power MOSFET
• IRF520 10A 100V N-Channel Power MOSFET
• IRF530 14A 100V N-Channel Power MOSFET
• IRF540 30A 100V N-Channel Power MOSFET
• IRF610 3.3A 200V N-Channel Power MOSFET
• IRF620 6A 200V N-Channel Power MOSFET
• IRF630 9A 200V N-Channel Power MOSFET
• IRF634 8.1A 250V N-Channel Power MOSFET
• IRF640 18A 200V N-Channel Power MOSFET
• IRF644 14A 250V N-Channel Power MOSFET
• IRF720 3.3A 400V N-Channel Power MOSFET
• IRF730 5.5A 400V N-Channel Power MOSFET
• IRF740 10A 400V N-Channel Power MOSFET
• IRF820 2.5A 500V N-Channel Power MOSFET
• IRF830 4.5A 500V N-Channel Power MOSFET
• IRF840 8A 500V N-Channel Power MOSFET
• IRF1010N 85A 55V N-Channel Power MOSFET
• IRF1404 202A 40V N-Channel Power MOSFET
• IRF1405 169A 55V N-Channel Power MOSFET
• IRF3205 110A 55V N-Channel Power MOSFET
• IRF3315 27A 150V N-Channel Power MOSFET
• IRF3415 43A 150V N-Channel Power MOSFET
• IRF3710 57A 100V N-Channel Power MOSFET
• IRF4905 74A 55V P-Channel Power MOSFET
• IRF5210 40A 100V P-Channel Power MOSFET
• IRF5305 31A 55V P-Channel Power MOSFET
• IRF9520 6.8A 100V P-Channel Power MOSFET
• IRF9530 12A 100V P-Channel Power MOSFET
• IRF9531 12A 60V P-Channel Power MOSFET
• IRF9532 10A 100V P-Channel Power MOSFET
• IRF9533 10A 60V P-Channel Power MOSFET
• IRF9540 23A 100V P-Channel Power MOSFET
• IRF9610 1.8A 200V P-Channel Power MOSFET
• IRF9630 6.5A 200V P-Channel Power MOSFET
• IRF9640 11A 200V P-Channel Power MOSFET
• IRF9Z34N 19A 55V P-Channel Power MOSFET
• IRFBG30 3.1A 1000V N-Channel Power MOSFET
• IRFD014 1.7A 60V N-Channel Power MOSFET
• IRFD024 2.5A 60V N-Channel Power MOSFET
• IRFD110 1A 100V N-Channel Power MOSFET
• IRFD120 1.3A 100V N-Channel Power MOSFET
• IRFD9014 1.1A 60V P-Channel Power MOSFET
• IRFD9024 1.6A 60V P-Channel Power MOSFET
• IRFD9120 1A 100V P-Channel Power MOSFET
• IRFP140 33A 100V N-Channel Power MOSFET
• IRFP150 42A 100V N-Channel Power MOSFET
• IRFP240 20A 200V N-Channel Power MOSFET
• IRFP250 33A 200V N-Channel Power MOSFET
• IRFP254 23A 250V N-Channel Power MOSFET
• IRFP260 50A 200V N-Channel Power MOSFET
• IRFP350 16A 400V N-Channel Power MOSFET
• IRFP450 14A 500V N-Channel Power MOSFET
• IRFP460 20A 500V N-Channel Power MOSFET
• IRFP9240 12A 200V P-Channel Power MOSFET
• IRFZ14 10A 60V N-Channel Power MOSFET
• IRFZ24N 17A 55V N-Channel Power MOSFET
• IRFZ34 26A 55V N-Channel Power MOSFET
• IRFZ44 49A 55V N-Channel Power MOSFET
• IRFZ46 50A 50V N-Channel Power MOSFET
• IRFZ48 50A 60V N-Channel Power MOSFET
• IRL520 10A 100V N-Channel Power MOSFET
• IRL540 36A 100V N-Channel Power MOSFET

Additional Information:

• Port of Dispatch: Mumbai
• Delivery Time: EX-Stock

The 6N136 is an optocoupler with a GaAIAs infrared emitting diode, optically coupled with an integrated photo detector which consists of a photo diode and a high-speed transistor in a DIP8 plastic package. Signals can be transmitted between two electrically separated circuits up to frequencies of 2 MHz. The potential difference between the circuits to be coupled should not exceed the maximum permissible reference voltages.

 

Features of 6N136 Optocoupler:

• Isolation test voltages 5300 VRMS
• TTL compatible
• High bit rates 1 Mbit/s
• High common-mode interference immunity
• Bandwidth 2 MHz
• Open-collector output
• External base wiring possible
• Ambient temperature range (Tamb) -55 to +100 DegreeC
• Soldering temperature max. 10 s, dip soldering 0.5 mm from case bottom (Tsld) 260 DegreeC
• Maximum output current 16mA
• Base current (IB) 5mA

2P4M 2A Plastic Molded ThyristorThe2P4Mis a p-gate, all diffused plastic molded typeSCRwith average On Time current of 2Amps with rated voltage up to 600V. It can be used a general purposethyristorin variety of power control applications.


Features of 2P4M:

• Less Holding Current distribution provides free application design.
• Easy Installation by its miniature size and thin electrode leads.
• Low Cost.

Applications of 2P4M:

• Electric Blanket
• Electronic jar
• various Temperature Control
• Electric sewing machine
• Light Display equipment
• Lamp Dimmer
• Battery Charger

The6N137is single channel 10 MBd opto-couplers utilizing a high efficient input LED coupled with an integrated optical photodiode IC detector. The detector has an open drain NMOS-transistor output, providing less leakage compared to an open collector Schottky clamped transistor output. For the single channel type, an enable function on pin 7 allows the detector to be strobed. The use of a 0.1 F bypass capacitor connected between pin 5 and 8 is recommended.

 

Features of 6N137 High-Speed Opto-coupler:

• Choice of CMR performance of 15 kV/s, 5 kV/s, and 1000 V/s
• High speed 10 MBd typical
• +5 V CMOS compatibility
• Pure tin leads
• Guaranteed AC and DC performance over
• Meets IEC 60068-2-42 (SO2) and IEC 60068-2-43 (H2S) requirements

 

Applications of 6N137 High-Speed Optocoupler:

• Microprocessor system interface
• PLC, ATE input/output isolation
• Computer peripheral interface
• Digital fieldbus isolation CC-link, DeviceNet, profibus, SDS
• High speed A/D and D/A conversion
• AC plasma display panel level shifting
• Multiplexed data transmission
• Digital control power supply
• Ground loop elimination, noise isolation

4N25 OptocouplerThe4N25is a general purpose 6-pinOptocoupler. It consists of a gallium arsenide infrared emitting diode driving a silicon phototransistor in a 6-pin dual in-line package. The applications of the 4N25 include Power supply regulators, Digital logic inputs, Microprocessor inputs.

Features of 4N25:

• Total Device Power Dissipation @ TA = 25 250 ;
• Derate above 25 3.3 (non-M), 2.94 (-M) mW;
• DC/Average Forward Input Current 100 (non-M), 60 (-M) mA;
• Forward Current - Peak (300s, 2% Duty Cycle) 3 A;
• LED Power Dissipation @ TA = 25 150 (non-M), 120 (-M) mW;
• Derate above 25 2.0 (non-M), 1.41 (-M) mW/.

PC817OPTOCOUPLER/PhotocouplerPC817 is a 4pin DIP General Purpose Photocoupler/Optocoupler.PC817 contains an IRED optically coupled to a phototransistor.

Features of PC817 Optocoupler:

• 4pin DIP package

• Double transfer mold package (Ideal for Flow Soldering)

• High collector-emitter voltage (VCEO80V)

• Current transfer ratio (CTR MIN. 50% at IF=5 mA,VCE=5V)

• Several CTR ranks available

• High isolation voltage between input and output(Viso(rms) 5.0 kV)

• Lead-free and RoHS directive compliant

Application of PC817 Photocoupler:

• Computer terminals

• System appliances, measuring instruments

• Registers, copiers, automatic vending machines

• Electric home appliances, such as fan, heaters, etc.

• Medical instruments, physical and chemical equipment

• Signal transmission between circuits of different potentials and impedances

TIP127 Darlington TransistorTIP127is aDarlington PNP Transistor. Itcomes in TO220AB Plastic case in package with collector current 5 Ampere.

Features of TIP127 Transistor:

• Collector-Emitter-voltage B open VCE0 100 V
• Collector-Base-voltage E open VCB0 100 V
• Emitter-Base-voltage C open VEB0 50 V
• Collector current IC 5 A
• Storage temperature TS - 65 + 150 DegreeC
• Recommended complementary NPN transistors TIP120, TIP121, TIP122

TIP122 Darlington TransistorsTIP122 is a Darlington NPN Transistors. It is available inTO220AB Plastic case in package with collector current 5 Ampere.


Features of TIP122 Transistor

• Collector-Emitter-voltage B open VCE0 100 V
• Collector-Base-voltage E open VCB0 100 V
• Emitter-Base-voltage C open VEB0 5 V
• Collector current IC 5 A
• Recommended complementary PNP transistors TIP125, TIP126, TIP127

Features of 4N35 Optocoupler:

• Gallium-Arsenide-Diode Infrared Source Optically Coupled to a Silicon npn Photo-transistor
• High Direct-Current Transfer Ratio
• High-Voltage Electrical Isolation 1.5-kV, 2.5-kV, or 3.55-kV Rating
• High-Speed Switching tr = 7 s, tf = 7 s Typical
• Input-to-output root-mean-square voltage (8-ms half sine wave)4N35= 2.5 kV
• Collector-emitter voltage=30 V
• Emitter-base voltage=7 V
• Input-diode reverse voltage=6 V
• Typical Applications Include Remote Terminal Isolation, SCR and Triac Triggers, Mechanical Relays and Pulse Transformers

TLP250 Opto-CouplerTLP250 comes in 8 pin DIP package and consists of a GaAlAs light emitting diode and a integrated photodetector.It is suitable for gate driving circuit of IGBT or power MOSFET.

Features of TLP250 Optocoupler:

• Input threshold current IF=5mA(max.)
• Isolation voltage 2500Vrms(min.)
• UL recognized UL1577, file No.E67349
• Option (D4) type
• Maximum operating insulation voltage 630VPK
• Highest permissible over voltage 4000VPK